This document describes the HydrOffice QC Tools 2 application (2.7). For the project page, go here.
2.3.6. Scan features¶
2.3.6.1. How To Use?¶
Scan features to ensure proper attribution and cartographic disposition.
- Select the Scan Features tab on the bottom of the QC Tools interface.
- In Parameters (Fig. 2.40, left side), turn the knob to select the required year of HCell Specification. Currently, the ‘2018 test’ is duplicative to 2016.
- In Execution (Fig. 2.40, right side), click Feature scan v2.
- After computing, the output window opens automatically, and the results are shown (Fig. 2.41).
- From the output window, drag-and-drop the output into the processing software to guide the review.
- In addition, the results are printed to PDF for a documented summary.
2.3.6.2. How Does It Work?¶
The S-57 features are scanned to ensure proper attribution and chart disposition per the required year of HCell Specification. Listed within the specification are mandatory requirements and S-57 attribution.
The QC Tools Chart feature scan will ensure the following:
- No redundant features.
- CS Soundings have an accompanying SS Sounding.
- All feature VALSOU have an accompanying SS Sounding.
- No feature VALSOU coincide with a CS Sounding.
- No objects have prohibited attribute SCAMIN.
- No objects have prohibited attribute RECDAT.
- No objects have prohibited attribute VERDAT.
- All objects have mandatory attribute NINFOM. [1] [2014]
- All objects have SORIND. [2]
- All objects have SORDAT. [2]
- No SOUNDG have prohibited attribute STATUS.
- All Wrecks must have mandatory attributes CATWRK, WATLEV, VALSOU, and QUASOU.
- All Wrecks with WATLEV = 5 (awash) must have mandatory attribute EXPSOU. [2016]
- All UWTROC must have mandatory attributes VALSOU, WATLEV, and QUASOU.
- All OBSTRN must have mandatory attributes VALSOU, WATLEV, and QUASOU.
- No OBSTRN with CATOBS =6 (foul area). [2014]
- All MORFAC must have mandatory attribute CATMOR.
- No MORFAC have prohibited attributes BOYSHP, COLOUR, or COLPAT. [2016]
- All SBDARE points must have mandatory attribute NATSUR.
- No SBDARE points have prohibited attributes COLOUR or WATLEV.
- All SBDARE points have an allowable combination of NATSUR and NATQUA noted by ‘x’ in the table below.
NATQUA | 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | 9 | 10 | |
N A T S U R |
1 | o | o | o | o | o | o | ||||
2 | o | o | o | o | |||||||
3 | o | o | o | o | |||||||
4 | o | o | o | o | o | o | o | ||||
5 | o | o | |||||||||
6 | o | o | |||||||||
7 | o | o | |||||||||
8 | o | o | |||||||||
9 | o | o | |||||||||
11 | o | ||||||||||
14 | o | ||||||||||
17 | o | o | |||||||||
18 | o | o |
NATQUA: fine (1), medium (2), coarse(3), broken (4), sticky (5) soft (6), stiff (7), volcanic (8), calcareous (9), hard (10)
NATSUR: mud (1), clay (2), silt (3), sand (4), stone (5), gravel (6), pebbles (7), cobbles (8), rock (9), lava (11), coral (14), shells (17), boulder (18)
- All SBDARE lines and areas must have mandatory attribute NATSUR and WATLEV.
- All COALNE must have mandatory attribute CATCOA.
- No COALNE have prohibited attribute ELEVAT.
- All CTNARE must have mandatory attribute INFORM. [2016]
- All SLCONS must have mandatory attribute CATSLC.
- All M_QUAL must have mandatory attributes CATZOC, TECSOU, SURSTA, and SUREND.
- All M_CSCL must have mandatory attribute CSCALE.
- All M_COVR must have mandatory attribute CATCOV.
- All cartographic objects must have mandatory attributes NINFOM and NTXTDS. [3] [2014]
- All cartographic objects must have mandatory attribute INFORM. [3] [2016]
- All objects with NOAA extended attributes still populated are tallied and presented (display only) as a reminder to clear before final submission.
Footnotes
[1] | Excludes SOUNDG, M_COVR, M_QUAL, M_CSCL, and DEPARE. |
[2] | (1, 2) 2016 excludes LNDARE, DEPARE, and DEPCNT from the check for SORIND and SORDAT. |
[3] | (1, 2) Cartographic objects include $CSYMB, $LINES, and $AREAS. |
[2014] | (1, 2, 3) Only for 2014 HCell Specification |
[2016] | (1, 2, 3, 4) Only for 2016 HCell Specification |